INDUSTRIAL LASER CLEANING

Laser surface preparation before bonding and coating

Plan laser surface preparation before bonding, coating or welding. Define the treatment area, process objective and appropriate quality checks for your component.

Request equipment advice
Two perforated metal parts with differently coloured surfaces

REAL-WORLD FOOTAGE

Surface preparation in practice

The photo shows a surface and the video shows targeted texturing. Suitability for bonding, coating or welding must be tested against your process.

ROD Q: texturing a metal surface

Excerpt from “Laser roughness”. The overlaid Rz values come from the manufacturer video and were not independently measured by us.

Metal sample with two visibly different surface areas on a workshop table
Two visible surface zones

Manufacturer photo of a metal sample. Adhesion cannot be inferred from the image alone.

Would this process suit your part? These examples help frame the question; equipment selection depends on your materials, surfaces and requirements.

Explore equipment Request equipment

What the laser removes in pretreatment

Before bonding, coating or welding, whatever disturbs the joint has to come off the surface: oil and grease, release-agent residues, unstable top layers and oxides. Fraunhofer IFAM describes how short laser pulses evaporate such layers within fractions of a second. Pulsed lasers act only a few tens of nanometres to a few micrometres deep, and the base material is left unaffected.

Oil comes off too, although it barely absorbs the laser light. One manufacturer explains it like this: the oxide layer beneath the oil absorbs the beam and evaporates, and the resulting plasma tears away the transparent layer on top. The bare surface reoxidises at once, this time evenly. On aluminium this new, thin oxide layer is wanted.

This has little to do with other laser processes. Laser hardening and laser texturing change the material or its shape. Cleaning only takes away what does not belong. The article How does laser cleaning work? explains the removal in detail.

Before bonding: what pretreatment achieves

Bonding of aluminium is the best-studied case. In the German research project INTLASKLEB, TU Braunschweig and an industrial partner pretreated car-body sheet with a pulsed laser, bonded it with a hot-curing epoxy adhesive and measured the lap-shear strength: once fresh, and once after ten cycles of a climate test with salt spray, heat and frost.

Source: Stammen, Böhm, Dilger, Lammel, adhäsion 9/2005, table 1 (alloy Al 6016, adhesive Betamate 1496, test to DIN EN 1465, laser parameter LP 6). Values from a research project, no commitment for your component.

Freshly bonded, there is hardly any difference. After ageing, the sample that was only degreased has lost about 70% of its strength, the laser-pretreated one 14%. The setting that removed the whole oxide layer evenly did best. The adhesive was applied directly after the laser step.

With titanium the picture is similar. Fraunhofer IFAM compared bonds after a pressure-cooker test: samples cleaned only with isopropanol or an alkaline cleaner lost over 90% of their strength. Laser-pretreated and pickled samples lost 50%.

The laser is not always better. In a study on stainless steel, cleaning with acetone reached 28.7 MPa, laser texturing 27.5 MPa and sandblasting 22 MPa. The authors conclude that cleanliness matters more than roughness. In the studies, the advantage of the laser shows above all after ageing.

For load-bearing bonds Germany has DIN 2304-1. It treats bonding as a special process whose result cannot be fully tested non-destructively on the finished part. Pretreatment is a separate item of production there. According to Fraunhofer IFAM, about 90% of bonding defects go back to a lack of bonding know-how.

Before coating: cleanliness and roughness

A coating needs two things: a clean surface and, depending on the system, a certain roughness. Pure laser cleaning delivers the first. The second is a separate step, though the laser can do that too. In the LaserRep research project of Fraunhofer IFAM the laser reached the roughness of Rz = 70 µm required under ISO 12944 and left one order of magnitude less salt on the surface than mechanical methods.

How well the coating held afterwards is shown on the laser rust removal page. One manufacturer gives cross-cut values of 0 to 1 for paint pretreatment and concedes that complex three-dimensional geometry and parts made of elastomer or plastic set limits. The standards for preparing steel, ISO 8501-1 and ISO 12944-4, do not yet list the laser.

Before welding and brazing

Here the laser has arrived in series production. A narrow stripe is cleaned, exactly as wide as the seam. For a track width of 20 mm one manufacturer gives about 15 m per minute on aluminium sheet, up to 20 m per minute on shop primer and up to 10 m per minute for de-oiling steel. Older documents from the same manufacturer give 5 m per minute for aluminium; the laser power is not stated in either case.

With aluminium the issue is pores. Hydrogen from oxide, moisture and lubricant dissolves in the melt and stays behind as a pore on solidification. How far laser cleaning reduces porosity is shown with measured values on the weld cleaning page. On galvanised steel the zinc layer is not damaged, according to the manufacturer; what is removed are the zinc hydrates at the surface, which calms the weld pool.

The shortest times come from battery production: contact areas of cells are cleaned before wire bonding at about 50 cm² per second, and a ground point takes less than one second. These are figures from a laser manufacturer for automatic systems.

Degreasing with the laser: what works and where it ends

The laser removes thin oil and grease films reliably. As an upper limit, one manufacturer names oil layers of up to 4 g/m² that were removed reliably from aluminium sheet at more than 12 m per minute. The process is not meant for thick layers: more than 0.5 mm is usually uneconomic, especially over several square metres.

Degreasing: laser and aqueous parts cleaning compared
LaserpulsedAqueous cleaningwashing system
Cleaning only the jointfits well: made for thispoor fit: no partial cleaning
Bores, cooling channels, inner areaspoor fit: the beam does not get infits well: reaches them
Flushing out chipspoor fit: not possiblefits well: yes
Space and mediafits well: no bath, no waste waterwith limits: three to nine stages, usually over 20 m²

fits wellwith limitspoor fit

The comparison comes from a laser manufacturer that names the limits of its own process. The washing system reaches inner areas and flushes out chips; the laser cannot replace that. Clear coat cannot be removed properly at 1064 nm either, according to one manufacturer.

On safety: the German accident insurers’ paper on laser cleaning says nothing specific about oil and grease. Its general rules apply. The beam can ignite flammable substances, the work counts as hot work, and the working area is to be kept free of flammable materials that are not needed. Name oil and grease residues in the enquiry together with their known ingredients.

Removing an oxide layer: hitting the window

An oxide layer has a lower ablation threshold than the metal beneath. The beam can therefore be set to take only the oxide. Below that too little happens, above it too much. A study on titanium shows the window in three steps:

Fluence Result on the titanium surface
2.55 J/cm² oxide layer only partly removed
6.37 J/cm² completely removed, roughness 0.37 µm
8.91 J/cm² too much ablation, the surface reoxidises and turns yellowish brown

The same holds for aluminium. If the beam moves too slowly, the metal itself is attacked once the oxide is gone, and too much power makes the surface oxidise again. That is a reason for a trial on your own material before parameters are fixed. For copper oxide we found no reliable measurements.

How cleanliness is checked

A specification such as “clean” is too vague. What is tested is whether a liquid wets the surface, or how much organic residue is still on it. Four methods are common:

Test methods

Four ways to check the pretreatment

Test inkQuick, but not very objective. An ink of known surface tension is brushed on. If the film stays intact, the surface energy of the part is higher. The verdict depends on the tester.

Contact angleOne of the most reliable methods. A drop is placed on the surface and its contact angle is measured. Suited to small areas and local checks, also with mobile instruments at the line.

Water breakFor large parts. The part is dipped or wetted and you watch where the water film tears. Simple, but hard to judge objectively.

FluorescenceMeasures residues directly. Violet or ultraviolet laser light makes organic residues such as oils, release agents or fingerprints fluoresce. The detection limit is 1 to 10 mg per square metre.

According to Fraunhofer IFAM and Fraunhofer IPM. Which test counts is set by the next process.

Agree the assessment with those responsible for production and quality. Record which test is planned and which value counts as release.

Inspection plan before the next operation

Before release, record what needs inspecting, where, who agrees the criterion and which details are still missing. Choose “Unknown / to be clarified” for unresolved points.

Metal sample, blank planning cards and pencil on a table
Illustrative image (AI-generated)
What the methods assess

Fraunhofer IFAM describes contact angle, test inks and water break as methods for assessing wettability. Fraunhofer IPM describes fluorescence for detecting organic contamination. These are different inspection targets. Agree the method and acceptance criterion for your component with those responsible for the next process.

Fraunhofer IFAM · Fraunhofer IPM

Planning note, no release: these entries do not confirm surface suitability. This tool selects neither a machine nor laser parameters.

Without JavaScript: use these questions as a checklist and record the answers separately.

  1. What follows cleaning?
  2. What should the inspection assess?
  3. Which inspection method is planned?
  4. Which role agrees the acceptance criterion?
  5. Which material and area will be inspected? Component reference, inspection areas and areas that must stay unchanged.
  6. Which requirement applies, and how will the result be assessed and recorded? If known: document reference, property, assessment rule and test equipment. Leave missing requirements open.
  7. Which details are still missing from the inspection plan? For example: inspection areas, test conditions, reference sample, handling or handover to the next process. Do not enter contact details.

How long the surface stays usable

No standard sets a time limit for laser-treated metal, and measured values are few. In one study laser-textured surfaces were completely wettable directly after treatment, with contact angles close to 0°. In ambient air the angle rose to 13.6° on stainless steel after three days and to 8.1° on aluminium after twelve days. The authors attribute this to organic compounds from the air settling on the surface.

One manufacturer writes that laser-treated metal surfaces are storable and can still be joined safely several days later. It gives no test data for this. In the INTLASKLEB research project the adhesive was applied directly after the laser step. So look at the time between cleaning and the next process and at the handling in between: who moves the part on, and where is it stored?

Plastics and CFRP

Plastics and fibre-reinforced composites need separate evaluation. Suitability for metals must not be applied automatically to these materials. According to one manufacturer, activation with infrared lasers works only on pigmented plastics; transparent release agents are removed together with the top layer of plastic. On CFRP, one study removed the resin selectively without damaging the fibres, and the bond strength matched that of manually abraded samples. UV and CO₂ lasers were used there, not fibre lasers at 1064 nm.

What belongs in the equipment enquiry

Equipment selection starts with what the next step requires. Which areas will be joined or coated? Which residues are present? And which test releases the surface? Define the zone on the component and record which neighbouring areas must stay unchanged.

What does a machine for surface preparation cost?

Describe the material, the contamination and the next process step. The price is stated in the quote.

Request pricing

For recurring parts, automotive production provides the process context, and the page on automated laser cleaning lists what a system needs to know. In your equipment request, state the material, the layer to be removed, component variants and the target condition.

Sources & further reading

YOUR NEXT STEP TOWARDS EQUIPMENT

Planning to buy a laser cleaning machine?

Describe your application and intended use to prepare equipment selection.

Request a quote